NEC Computer Monitor FE791SB User Manual

User's Manual

1. A Version

MultiSync FE791^SB/FE991^SB

1-1

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE

THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS

CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK • DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this

unit has been included. Therefore, it should be read carefully in order to avoid any problems.

Canadian Department of Communications Compliance Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations

according to C.S.A. C22.2 No. 950.

FCC Information

1.UsetheattachedspecifiedcableswiththeMultiSync FEcolormonitorsoasnottointerferewith

radio and television reception.

(1) Please use the supplied power cord or equivalent to ensure FCC compliance.

(2) Shielded captive type signal cable.

Use of other cables and adapters may cause intereference with radio and

television reception.

2. This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

televisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuser

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiver

is connected.

• Consult your dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

If necessary, the user should contact the dealer or an experienced radio/television

technician for additional suggestions. The user may find the following booklet, prepared

by the Federal Communications Commission, helpful: ”How to Identify and Resolve

Radio-TV Interference Problems.“ This booklet is available from the U.S. Government

Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

1-3

Contents

Your new NEC MultiSync^®FE monitor box* should contain the

following:

• MultiSync FE Monitor with tilt/swivel base

• Power Cord

• Captive Signal Cable

• User’s Manual

Captive Signal Cable

MultiSync FE791^SB/FE991^SB

Power Cord

User’s Manual

* Remember to save your original box and packing material to transport or ship the monitor.

1-4

Quick Start

To attach the FE monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. If necessary, install the display card into your system. For more information,

refer to the display card manual.

3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable to the

connector of the display card in your system (Figure A.1). Tighten all screws.

For the Mac: Connect the MultiSync FE Macintosh cable adapter (not included)

to the monitor connector on the Macintosh (Figure B.1). Attach the 15-pin

mini D-SUB end of the captive signal cable to the MultiSync FE Macintosh

cable adapter on the computer (Figure B.1). Tighten all screws.

NOTE: To obtain the MultiSync FE Macintosh cable adapter, call

NEC-Mitsubishi Electronics Display of America, Inc. at (800) 632-4662.

4. For download information on the Windows^®95/98/Me/2000/XP INF file

for your MultiSync monitor, refer to the References section of this User’s

Manual.

5. Connect one end of the power cord to the MultiSync FE monitor and the other

end to the power outlet (Figure C.1).

6. Turn on the monitor (Figure D.1) and the computer.

NOTE: If you have any problems, please refer to the Troubleshooting section of

this User’s Manual.

Figure A.1

Figure B.1

15-pin

mini

D-SUB

Mac Adapter

(Not Included)

Captive Signal Cable

1-5

Quick Start

–continued

Figure C.1

Power Button

Figure D.1

1-6

Controls

OSM^™(On-Screen Manager) control buttons on the front of the monitor function

as follows:

Main Menu

Sub-Menu

EXIT

Exits the OSM menu.

Exits to the OSM controls

main menu.

CONTROL

Moves the highlighted

area left/right to select

one of the sub-menus.

Moves the highlighted area

left/right to select one of the

controls.

CONTROL

–/+

Has no function.

Moves the bar in the – or +

direction to decrease or

increase the adjustment.

SELECT/

Enters sub-menu.

Has no function.

SBMODE

RESET

Resets all the controls within

the highlighted menu

Resets the highlighted control

to the factory setting.

NOTE:

When RESET is pressed in the main and sub-menu, a warning window will appear

allowing you to cancel the reset function.

When the OSM is off, it will act as the SuperBright (SB) function key. User can select

between SB MODE OFF, SB MODE1, and SB MODE2. The first time this key is

pressed, the current SB Mode is indicated. Within a 3 second window, if this key is

selected again, the SB MODE will change to the next SB MODE. For example, the

current mode is SB MODE OFF, the key is pressed twice within a 3 second time frame,

the SB MODE will change to SB MODE1 and so on. The color temperature at each SB

Mode is adjusted by appropriate color control except for the sRGB mode whose color

setting cannot be adjusted. When the unit is turned off, it will reset to SB off mode.

Brightness/Contrast Controls

Brightness: Adjusts the overall image and background screen brightness.

Contrast: Adjusts the image brightness in relation to the background.

Degauss: Eliminates the buildup of stray magnetic fields which alter the correct

scan of the electron beams and affect the purity of the screen colors, focus and

convergence. When activated, your screen image will jump and waver a bit as

the screen is demagnetized.

Caution: Please allow a minimum of 20 minutes to elapse between uses

of the Degauss Control.

Size and Position Controls

Left/Right: Moves the image horizontally (left or right).

Down/Up: Moves the image vertically (up or down).

Narrow/Wide: Decreases or increases the horizontal size of the image.

Short/Tall: Decreases or increases the vertical size of the image.

1-7

Controls

–continued

Color Control/AccuColor^®Control System

Color presets selects the desired color setting. The bar is replaced by the color

setting choice. Each color setting is adjusted at the factory to the stated Kelvin. If

a setting is adjusted, the name of the setting will change from Kelvin to Custom

except sRGB mode.

Red, Green, Blue: AccuColor Control System decreases or increases the

monitor's red, green or blue color guns depending upon which is selected. The

change in color will appear on screen and the direction (decrease or increase)

will be shown by the bars.

sRGB mode: sRGB mode provides the suitable color managed picture image. You

can not change Red, Green and Blue colors, brightness and contrast individually.

Color Temperature Adjustment: Adjusts the color temperature of the screen image.

Geometry Controls

Geometry Controls Menu

The Geometry controls allow you to adjust the curvature or angle of the sides of

your display.

Sides In/Out (pincushion): Decreases or increases the curvature of the sides either

inward or outward.

Sides Left/Right (pincushion balance): Decreases or increases the curvature of

the sides either to the left or right.

Sides Tilt (parallelogram): Decreases or increases the tilt of the sides either to the

left or right.

Sides Align (trapezoidal): Decreases or increases the bottom of the screen to be

the same as the top.

Rotate (raster rotation): Rotates the entire display clockwise or counterclockwise.

Corner Correction: Allows you to adjust the geometry of the corners of your

display

—

Top or Bottom.

Tools 1

Moiré Canceler: Moiré is a wavy pattern which can sometimes appear on the screen.

The pattern is repetitive and superimposed as rippled images. When running certain

applications, the wavy pattern is more evident than in others. To reduce moiré, adjust

the level by using –/+ CONTROL buttons.

Linearity: This selection allows you to adjust the spacing of the area on the screen. The

purpose of this control is to ensure that a one-inch circle is a true one-inch circle wherever

it is on the screen. The best way to determine the vertical linearity is as follows:

•Draw equally spaced horizontal lines using a drawing application that has a ruler.

•

Use the Vertical Balance control to adjust the lines near the top and bottom of your screen.

•Use the LINEARITY (VER.) control to adjust the spacing between the lines near the

center and top of your screen.

Convergence (FE991SB only) : Aligns all three colors (R,G,B) to form a single

color (white). The purpose of this control is to ensure that a white line drawn on

the screen is as crisp and clear as possible.

1-8

Controls

–continued

• Use the CONVERGENCE (HOR.) control to adjust the alignment of the lines in the up/

down direction.

•

Use the CONVERGENCE (VER.) control to adjust the alignment of the lines in the left/right

direction.

Tools 2

Language: OSM controls menus are available in 6 languages.

OSM Position: You can choose where you would like the OSM controls menu to

appear on your screen. Selecting OSM Position allows you to manually adjust the

OSM controls menu position from among Center, Top left, Top right, Bottom left

and Bottom right.

OSM Turn Off: The OSM controls menu will stay on as long as it is in use. In the

OSM Turn Off sub-menu, you can select how long the monitor waits after the last

touch of a button for the OSM controls menu to disappear. The preset choices

are 10 thru 120 seconds.

SM Lock Out: This control completely locks out access to all OSM controls

functions except Brightness and Contrast. When attempting to activate OSM

controls while in the lock out mode, a screen will appear indicating that OSM

controls are locked out. To activate the OSM Lock Out function, press SELECT and

hold down simultaneously. To deactivate the OSM Lock Out, press SELECT and

hold down simultaneously.

IPM^™System Off Mode: Enable: The IPM System works normally and all

stages of energy savings are utilized.

Disable: The Off Mode of the IPM System is not used.

OTE: For standard systems and graphics boards, keep the factory setting

at ENABLE

EdgeLock^™Control: Operating your monitor at a nonstandard timing may cause

images to appear darker than normal or have color distortion. Use of the

EdgeLock control will adjust images to their normal state.

Hot Key: This selection allows you to use

as brightness control and –/+

as contrast control.

Factory Preset: Selecting Factory Preset allows you a reset most OSM^™control

settings back to the factory settings. A warning statement will appear to confirm

that you do want to reset ALL settings. Individual settings can be reset by high-

lighting the control to be reset and pressing the RESET button.

Information

Display Mode: Indicates the current mode and frequency setting of the monitor.

Monitor Info: Indicates the model and serial numbers of your monitor.

Refresh Notifier: A message will advise you if the refresh rate of the signal being

applied to the monitor by the computer is too low. For further information, please

refer to your display card or system manual.

1-9

Recommended Use

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE MULTISYNC^®FE COLOR MONITOR:

DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or

removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to

qualified service personnel.

•

Do not spill any liquids into the cabinet or use your monitor near water.

Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage

points, which can be harmful or fatal or may cause electric shock, fire or equipment failure.

Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.

Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall,

causing serious damage to the monitor.

•

Keep the monitor away from high capacity transformers, electric motors and other devices such as

external speakers or fans, which may create strong magnetic fields.

If possible, position the monitor so that it is facing the east to minimize the effects of the earth’s

magnetic field.

Changing the direction of the monitor while it is powered on may cause image discoloration. To

correct this, turn the monitor off for 20 minutes before powering it back on.

When operating the MultiSync FE with its AC 220-240V worldwide power supply, use a power

supply cord that matches the power supply voltage of the AC power outlet being used. The power

supply cord you use must have been approved by and comply with the safety standards of your

country. (Type H05VV-F should be used except in UK)

•

In UK, use a BS-approved power cord with molded plug having a black (5A) fuse installed for use with

this monitor. If a power cord is not supplied with this monitor, please contact your supplier.

Cleaning Your Monitor

A special coating is provided on the glass (CRT) surface of this monitor to reduce a reflection and

static electricity on the glass surface. Due to the delicate coating on the glass surface, use a lint-free,

non-abrasive cloth (cotton or equivalent) and a non-alcohol, neutral, non-abrasive cleaning solution

to minimize dust. If the screen requires more than a light cleaning, apply a soft neutral detergent and

water directly to a soft cloth and use it upon wringing water, to clean the glass surface. Clean your

monitor regularly.

CAUTION: The following agents will cause damage to the CRT when cleaning the glass surface:

Benzene, thinner, acid/alkaline detergent, alcohol detergent, detergent with abrasive powder,

detergent with anti-static agent, detergent for cleaning.

Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel

under the following conditions:

•

When the power supply cord or plug is damaged.

If liquid has been spilled, or objects have fallen into the monitor.

If the monitor has been exposed to rain or water.

If the monitor has been dropped or the cabinet damaged.

If the monitor does not operate normally by following operating instructions.

•

Allow adequate ventilation around the monitor so that heat can properly

dissipate. Do not block ventilated openings or place the monitor near a

radiator or other heat sources. Do not put anything on top of monitor.

The power cable connector is the primary means of detaching the system

from the power supply. The monitor should be installed close to a power

outlet which is easily accessible.

CAUTION

Handle with care when transporting. Save packaging for transporting.

1-10

Recommended Use

–continued

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR

CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE

FOLLOWING WHEN YOU POSITION THE MONITOR:

• Adjust the monitor height so that the top of

the screen is at or slightly below eye level.

Your eyes should look slightly downward

when viewing the middle of the screen.

• Position your monitor no closer than 16 inches

and no further away than 24 inches from your

eyes. The optimal distance is 20 inches.

• Rest your eyes periodically by focusing on

an object at least 20 feet away. Blink often.

• Position the monitor at a 90° angle to

windows and other light sources to minimize

glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect

on your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a

non-alcohol, neutral, non-abrasive cleaning solution or glass cleaner to

minimize dust.

• Adjust the monitor’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or

reference material) directly in front of you to minimize turning your head

while you are typing.

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Adjust the Brightness until the background raster disappears

• Do not position the Contrast control to its maximum setting

• Use the preset Size and Position controls with standard signals

• Use the preset Color Setting and Sides Left/Right controls

• Use non-interlaced signals with a vertical refresh rate between 75-120Hz

• Do not use primary color blue on a dark background, as it is difficult to see

and may produce eye fatigue due to insufficient contrast

For more detailed information on setting up a healthy work environment, call NEC -

Mitsubishi Electronics Display of America at (888) NEC-MITS, NEC FastFacts^™information

at (800) 366-0476 and request document #900108 or write the American National

Standard for Human Factors Engineering of Visual Display Terminal Workstations – ANSI-

HFS Standard No. 100-1988 – The Human Factors Society, Inc. P.O. Box 1369, Santa

Monica, California 90406.

1-11

Specifications

Monitor

MultiSync^®FE791

Notes

Specifications

Picture Tube

Monitor

17 inch

Diagonal:

90° deflection, 0.25 mm grille pitch,

medium short persistence phosphor,

aperture grille CRT, multi-layered,

anti-static screen coating, dark-tint screen

and OptiClear^®screen.

Viewable Image Size:

Radius:

16 inch

50,000 mm

Input Signal

Video:

Sync:

ANALOG 0.7 Vp-p/75 Ohms

Separate sync. TTL Level

Horizontal sync. Positive/Negative

Vertical sync. Positive/Negative

Composite sync. (Positive/Negative) (TTL Level)

Display Colors

Analog input:

Unlimited number of Colors

Depends on display card used.

Synchronization

Range

Horizontal:

Vertical:

30 kHz to 96 kHz

50 Hz to 160 Hz

Automatically

ResolutionsSupported

640 x 480 @ 60 to 160 Hz

800 x 600 @ 50 to 146 Hz

832 x 624 @ 50 to 141 Hz

Some systems may not support

all modes listed.

Resolution based onhorizontal and

verticalfrequenciesonly

1024 x 768 @ 50 to 116 Hz ...................... NEC-MitsubishiElectronicsDisplaycites

1152 x 870 @ 50 to 103 Hz

1280 x 1024 @ 50 to 89 Hz

1600 x 1200 @ 50 to 76 Hz

recommended resolution at 85 Hz for

optimal display performance.

Active Display Area

(Factory Setting)

Horizontal:

Vertical:

315 mm/12.4 inches

236 mm/9.3 inches

Dependent upon signal timing used,

and does not include border area.

Active Display Area

(Full Scan)

325 mm/12.8 inches

244 mm/9.6 inches

Dependent upon signal timing used,

and does not include border area.

Power Supply

CurrentRating

Dimensions

AC 100 – 240 V, 50-60 Hz

1.9A @ 100-240 V

397 mm (W) x 392 mm (H) x 415.5 mm (D)

15.6 inches (W) x 15.4 inches (H) x 16.4 inches (D)

Weight

17.2 kg

37.9 lbs

Environmental Considerations

Operating Temperature:

Humidity:

+5°C to +35°C / +50°F to +90°F

10% to 90%

Feet:

0 to 10,000 Feet

Storage Temperature:

Humidity:

-20°C to +60°C / -4°F to +140°F

10% to 90%

Feet:

0 to 50,000 Feet

NOTE: Technical specifications are subject to change without notice.

1-12

Specifications

–continued

Monitor

MultiSync^®FE991

Monitor

Notes

Specifications

Picture Tube

Diagonal:

19 inch

90° deflection, 0.25/0.27 mm grille pitch,

medium short persistence phosphor,

aperture grille CRT, multi-layered,

anti-static screen coating, dark-tint screen

and OptiClear^®screen.

Viewable Image Size:

Radius:

18 inch

50,000 mm

Input Signal

Video:

Sync:

ANALOG 0.7 Vp-p/75 Ohms

Separate sync. TTL Level

Horizontal sync. Positive/Negative

Vertical sync. Positive/Negative

Composite sync. (Positive/Negative) (TTL Level)

Display Colors

Analog input:

Unlimited number of Colors

Depends on display card used.

Synchronization

Range

Horizontal:

Vertical:

30 kHz to 96 kHz

50 Hz to 160 Hz

Automatically

Resolutions Supported

640 x 480 @ 60 to 160 Hz

800 x 600 @ 50 to 146 Hz

832 x 624 @ 50 to 141 Hz

1024 x 768 @ 50 to 116 Hz

1152 x 870 @ 50 to 103 Hz

Some systems may not support

all modes listed.

Resolution based on horizontal and

vertical frequencies only

NEC-Mitsubishi Electronics Display cites

recommended resolution at 85 Hz for

1280 x 1024 @ 50 to 89 Hz ..................... optimal display performance.

1600 x 1200 @ 50 to 76 Hz

1792 x 1344 @ 50 to 68 Hz

Active Display Area

(FactorySetting)

Horizontal:

Vertical:

356 mm/14.0 inches

266 mm/10.5 inches

Dependent upon signal timing used,

and does not include border area.

Active Display Area

(FullScan)

366 mm/14.4 inches

274 mm/10.8 inches

Dependent upon signal timing used,

and does not include border area.

Power Supply

CurrentRating

Dimensions

AC 100 – 240 V, 50-60 Hz

2.2A @ 100-240 V

442 mm (W) x 443 mm (H) x 447.5 mm (D)

17.4 inches (W) x 17.4 inches (H) x 17.6 inches (D)

Weight

22.7 kg

50.0 lbs

Environmental Considerations

Operating Temperature:

Humidity:

+5°C to +35°C / +50°F to +90°F

10% to 90%

Feet:

0 to 10,000 Feet

Storage Temperature:

Humidity:

-20°C to +60°C / -4°F to +140°F

10% to 90%

Feet:

0 to 50,000 Feet

NOTE: Technical specifications are subject to change without notice.

1-13

Features

SuperBright^TMDiamondtron^®CRT : This patented flat aperture grille CRT delivers

an exceptional viewing experience with unprecedented brightness and contrast

and a virtually flat image that reduces distortion and glare so that what you see

on-screen is what you get on your printed output. The state-of-the-art Mitsubishi

PX-DBF^TMelectron gun and tight 0.25mm grille pitch delivers precise focus for

crisp, clear text and images.

SuperBright Mode : With the simple touch of a button, the brightness level of

the Diamondtron CRT doubles. This function enhances the crispness of images for

clarity-conscious applications such as graphics, animation and video.

Super Bright Mode OFF: for text based images (normal use)

Super Bright Mode-1 ON: for images

Super bright Mode-2 ON: for moving image such as DVD movies

OptiClear^®Screen Surface: Further reduces reflection and glare and increases

contrast without sacrificing focus level, clarity or brightness.

Dual Dynamic Beam Focus: Provides precise, continuous focus adjustments of the

electron beams and optimum image quality, even to the far edges of the screen.

AccuColor^®Control System with sRGB: Allows you to change between five color

settings on your display to match your personal preference. The sRGB-enabled

color matching setting found within AccuColor helps achieve a consistent color

environment with other sRGB-enabled hardware and software applications.

On Screen Manager (OSM^TM) Controls: Allows you to quickly and easily adjust

all elements of your screen image via simple to use on-screen menus.

ErgoDesign^®Features: Enhances human ergonomics to improve the working

environment, protect the health of the user and save money. Examples include

OSM controls for quick and easy image adjustments, tilt/swivel base for pre-

ferred angle of vision, space-conscious cabinet design and compliance with

MPRII guidelines for lower emissions.

Plug and Play: The Microsoft^®solution with the Windows^®95/98/Me/2000/XP

operating system facilitates setup and installation by allowing the monitor to send

its capabilities (such as screen size and resolutions supported) directly to your

computer, automatically optimizing display performance.

Intelligent Power Manager (IPM™) System: Provides innovative power-saving

methods that allow the monitor to shift to a lower power consumption level when

on but not in use, saving two-thirds of your monitor energy costs, reducing

emissions and lowering the air conditioning costs of the workplace.

1-14

Features

–continued

Reduced Magnetic Field™ Technology: Reduces magnetic and alternating

electric field emissions and static electricity, addressing ergonomic concerns

regarding potential risks from extended computer monitor use.

Multiple Frequency Technology: Automatically adjusts monitor to the display

card’s scanning frequency, thus displaying the resolution required.

FullScan™ Capability: Allows you to use the entire screen area in most

resolutions, significantly expanding image size.

1-15

Troubleshooting

No picture

• Display card should be completely seated in its slot.

• Power Button and computer power switch should be in the ON position.

• Signal cable should be completely connected to display card/computer.

• Check connector for bent or pushed-in pins.

Image is scrolling or unstable

• Signal cable should be completely attached to the computer.

• Check pin assignments and signal timings of the monitor and your display card with

respect to recommended timings and pin assignments.

•

If the Macintosh cable adapter is used, check for proper connection or make sure the

display card is Macintosh compatible and that the card is properly seated in the computer

LED on monitor is not lit (no green, orange color can be seen)

• Power Switch should be in the ON position and power cord should be connected.

LED on monitor is flashing and/or dissapears

• Contact Customer Service at (800) 462-4662.

Picture is fuzzy or color looks blotchy

• Adjust Brightness and Contrast Controls or adjust the Moiré Canceler control.

• Access the Degauss Control through OSM™ controls. Activate the Degauss Control.

CAUTION: A minimum interval of 20 minutes should elapse before the Deguass

Control is used a second time when not switching between modes.

Picture bounces or a wavy pattern is present in the picture

•

Move electrical devices that may be causing electrical interference away from the monitor.

• See inside cover of User’s Manual for FCC information.

Edges of the display image are not square

• Use the OSM Geometry Controls to straighten the edges.

• If possible, position the front of the monitor facing east.

Display image is not centered, too small, or too large

• Use the OSM Size and Position Controls to adjust the image.

Thin lines appear on your screen

• Thin lines are normal for an aperture grille CRT and are not a malfunction.

These are shadows from the damper wires used to stabilize the aperture grille and

are most noticeable when the screen’s background is light (usually white).

Black vertical lines are visible on the screen

• Thin vertical black lines on one or both sides of the screen. This minor condition is

caused by grille element overlap which can occur during shipping.

• Position an open white window over the affected area of the screen and maximize

the brightness and contrast controls. This will cause localized heating of the overlap

which will clear in a few minutes. Be sure to readjust the brightness and contrast

controls back to the normal viewing level after this procedure.

1-16

References

• BBS

(978) 742-8706

NEC-Mitsubishi Electronics Display of America Remote Bulletin Board System is

an electronic service accessible with your system and a modem. Communica-

tion parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no

parity, 8-data bits, 1 stop bit

• Customer Service/

Technical Support

Fax

(800) 632-4662

(978) 742-7049

• Electronic Channels:

Internet e-mail:

Internet ftp site:

[email protected]

ftp.necmitsubishi.com

World Wide Web:

Product Registration:

European Operations:

http://www.necmitsubishi.com

http://www.necmitsubishi.com/productregistration

http://www.nec-mitsubishi.com

Windows^®95/98/Me/2000/XP INF File: http://support.necmitsubishi.com/software.htm

then download the file NECMSINF.ZIP

• FastFacts™ Information

INFORMATION

(800) 366-0476

DESCRIPTION

DOCUMENT #

Glossary

Definition of terms related

to functions, features and

installation of the

900203

MultiSync^®monitor

More Information

Names and addresses of

other groups involved in

standards and features of

the MultiSync monitor

900204

Macintosh Connection

Detailed information on

connecting the MultiSync

monitor to a Macintosh

153006

900108

Healthy Work Environment

Detailed information on

setting up a healthy work

environment

• Literature & Sales Info

• MultiSync Fulfillment

(800) NEC-INFO [(800) 632-4636]

(800) 632-4662

[For software & accessories]

• TeleSales

(800) 284-4484

1-17

Limited Warranty

NEC-Mitsubishi Electronics Display of America, Inc. (hereinafter “NMD-A”) warrants this

Product to be free from defects in material and workmanship and, subject to the conditions set

forth below, agrees to repair or replace (at NMD-A’s sole option) any part of the enclosed unit

which proves defective for a period of three (3) years from the date of first consumer purchase.

Spare parts are warranted for ninety (90) days. Replacement parts or unit may be new or

refurbished and will meet specifications of the original parts or unit.

This warranty gives you specific legal rights and you may also have other rights, which vary

from state to state. This warranty is limited to the original purchaser of the Product and is not

transferable. This warranty covers only NMD-A-supplied components. Service required as a

result of third party components is not covered under this warranty. In order to be covered

under this warranty, the Product must have been purchased in the U.S.A. or Canada by the

original purchaser. This warranty only covers Product distribution in the U.S.A. or Canada by

NMD-A No warranty service is provided outside of the U.S.A. or Canada. Proof of Purchase

will be required by NMD-A to substantiate date of purchase. Such proof of purchase must be

an original bill of sale or receipt containing name and address of seller, purchaser, and the

serial number of the product.

It shall be your obligation and expense to have the Product shipped, freight prepaid, or

delivered to the authorized reseller from whom it was purchased or other facility authorized

by NMD-A to render the services provided hereunder in either the original package or a

similar package affording an equal degree of protection. All Products returned to NMD-A for

service MUST have prior approval, which may be obtained by calling 1-800-632-4662. The

Product shall not have been previously altered, repaired, or serviced by anyone other than a

service facility authorized by NMD-A to render such service, the serial number of the product

shall not have been altered or removed. In order to be covered by this warranty the Product

shall not have been subjected to displaying of fixed images for long periods of time resulting

in image persistence (afterimage effects), accident, misuse or abuse or operated contrary to

the instructions contained in the User’s Manual. Any such conditions will void this warranty.

NMD-A SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL,

OR OTHER TYPES OF DAMAGES RESULTING FROM THE USE OF ANY NMD-A PRODUCT

OTHER THAN THE LIABILITY STATED ABOVE. THESE WARRANTIES ARE IN LIEU OF ALL

OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE

LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAM-

AGES SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU.

This Product is warranted in accordance with the terms of this limited warranty. Consumers

are cautioned that Product performance is affected by system configuration, software, the

application, customer data, and operator control of the system, among other factors. While

NMD-A Products are considered to be compatible with many systems, specific functional

implementation by the customers of the Product may vary. Therefore, suitability of a Product

for a specific purpose or application must be determined by consumer and is not warranted

by NMD-A.

For the name of your nearest authorized NEC-Mitsubishi Electronics Display of America

service facility, contact NEC-Mitsubishi Electronics Display of America at 1-800-632-4662.

1-18

TCO’95

MultiSync^®FE Black Model

Congratulations! You have just purchased a TCO’95 approved and

labeled product! Your choice has provided you with a product devel-

oped for professional use. Your purchase has also contributed to

reducing the burden on the environment and also, to the further

development of environmentally adapted electronics products.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encourag-

ing the adaptation of goods and services to the environment. The main problem, as far as

computers and other electronics equipment are concerned, is that environmentally harmful

substances are used both in the products and during the manufacturing. Since it has not been

possible for the majority of electronics equipment to be recycled in a satisfactory way, most

of these potentially damaging substances sooner or later enter Nature.

There are also other characteristics of a computer, such as energy consumption levels, that are

important from the viewpoints of both the work (Internal) and natural (external) environments.

Since all methods of conventional electricity generation have a negative effect on the

environment (acidic and climate-influencing emissions, radioactive waste, etc.), it is vital to

conserve energy. Electronics equipment in offices consume an enormous amount of energy

since they are often left running continuously.

What does labelling involve?

This product meets the requirements for the TCO’95 scheme which provides for international and

environmental labelling of personal computers. The labelling scheme was developed as a joint

effort by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen

(The Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and

Technical Development in Sweden).

The requirements cover a wide range of issues: environment, ergonomics, usability, emission of

electrical and magnetic fields, energy consumption and electrical and fire safety.

The environmental demands concern restrictions on the presence and use of heavy metals,

brominatedandchlorinatedflameretardants, CFCs(freons)andchlorinatedsolvents, amongother

things. The product must be prepared for recycling and the manufacturer is obliged to have an

environmental plan which must be adhered to in each country where the company implements its

operational policy. The energy requirements include a demand that the computer and/or display,

after a certain period of inactivity, shall reduce its power consumption to a lower level in one or

more stages. The length of time to reactivate the computer shall be reasonable for the user.

Labelled products must meet strict environmental demands, for example, in respect of the reduction

of electric and magnetic fields, physical and visual ergonomics and good usability.

TCO’95 is a co-operative project between TCO (The Swedish Confederation of Professional

Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK

(The National Board for Industrial and Technical Development in Sweden).

Environmental Requirements

Brominated flame retardants

Brominated flame retardants are present in printed circuit boards, cables, wires, casings and

housings.Inturn,theydelaythespreadoffire.Uptothirtypercentoftheplasticinacomputercasing

can consist of flame retardant substances. These are related to another group of environmental

1-19

TCO’95

–continued

toxins, PCBs, which are suspected to give rise to similar harm, including reproductive damage in

fisheating birds and mammals, due to the bio-accumulative* processes. Flame retardants have

been found in human blood and researchers fear that disturbances in foetus development may

occur.

TCO’95 demand requires that plastic components weighing more than 25 grams must not contain

organically bound chlorine and bromine.

Lead**

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the

nervous system and in higher doses, causes lead poisoning.

TCO’95 requirement permits the inclusion of lead since no replacement has yet been developed.

Cadmium**

Cadmium is present in rechargeable batteries and in the colourgenerating layers of certain

computer displays. Cadmium damages the nervous system and is toxic in high doses.

TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of

cadmium. The colourgenerating layers of display screens must not contain any cadmium.

Mercury**

Mercuryissometimesfoundinbatteries, relaysandswitches, Mercurydamagesthenervoussystem

and is toxic in high doses.

TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of

mercury. It also demands that no mercury is present in any of the electrical or electronics

components concerned with the display unit. Mercury is, for the time being, permitted in the back

lightsystemofflatpanelmonitorsastheretodayisnocommerciallyavailablealternative.TCOaims

on removing this exception when a mercury free alternative is available.

CFCs (freons)

CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of

expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in

thestratosphere,causingincreasedreceptiononEarthofultravioletlightwithconsequentincreased

risks of skin cancer (malignant melanoma).

TherelevantTCO’95requirement;NeitherCFCsnorHCFCsmaybeusedduringthemanufacturing

of the product or its packaging.

*Bio-accumulative is defined as substances which accumulate within living organisms.

**Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

To obtain complete information on the environmental criteria document, order from:

TCO Development Unit

SE-114 94 Stockholm

SWEDEN

FAX Number: +46 8 782 92 07

E-mail (Internet): [email protected]

You may also obtain current information on TCO’95 approved and labelled products by

visiting their website at: http://www.tco-info.com/

1-20

TCO’99

MultiSync^®FE White Model

Congratulations! You have just purchased a TCO’99 approved and

labeled product! Your choice has provided you with a product devel-

oped for professional use. Your purchase has also contributed to

reducing the burden on the environment and also to the further